 |
 |
 |
|
| HID iClass RK40 Reader, Read Only Keypad, Wiegand Output, Terminal Strip, Tri-State LED, Standard iClass Elite Key, Internal Beeper On, Black |
|
|
|
|
|
 |
|
 |
|
Data Output Formats
The keypad reader reads standard proximity format data from HID iCLASS cards, and will output data as encoded. When reading MIFARE® cards, the keypad reader can be configured to output
26 bit, 32 bit, 34 bit, or 40 bit Wiegand formats based on the card serial number. Wiegand keypad data format can be configured for transmission of individual key presses as ASCII
encoded Hex digits, or for buffering and transmission of the PIN as a card number in SIA 26 bit format with a configurable facility code. Additionally, the RWK400 offers a bi-directional
serial port that communicates at data rates up to 57.6 Kbaud. Using the ISO 7816 protocol, the standard for contact smart card applications, the RWK400 allows connection to a PC or
microcontroller to support read/write applications.
Keypad
Twelve discrete switches are covered with a silicone rubber boot and vandal resistant metal keycaps. Raised tactile mark on "5" key for visually impaired users. Configurable audio feedback.
Backlit numbers in bezel overlay, above each key. Lighting is configurable: "Always On", "Always Off", "Triggered by Card Read", or "Triggered by Key Press".
Security
64 bit authentication keys are extremely secure. Readers and cards require matching keys to function. All RF data transmission between the card and keypad reader is encrypted, using a
secure algorithm. The key management system reduces the risk of compromised or duplicated cards. Cards and keypad readers with site-specific keys are optionally available from the factory.
Alternatively, the iCLASS CP400 Field Programmer® can be used to create site-specific keys. The programmer also allows users to create a keypad reader configuration card, which is used to
re-key cards and keypad readers on site.
Programming/Configuration
All cards are shipped with unique diversified keys; keypad readers are shipped with compatible keys. All keys are derived from the HID Standard key. While cards and keypad readers with
Standard keys are interchangeable, the keys are highly secure. Further enhance security by ordering with iCLASS Elite formatting.
Audiovisual Indication
Audio transducer provides configurable tone sequences to signify access granted, access denied, power up, and configuration card read. A light bar provides a clear visual status indication
in red, green, or amber.
Open Collector Output (RWK400 Only)
Normally Open logic output, controlled via serial port. Switches up to 50mA at 12 VDC. Use interposing relay for larger loads. Configurable to latch momentarily upon successful local
verification of PIN stored on the card.
Mounting
Mounting plate attaches to U.S./ EU/ Asian back box, 52-60 mm screw hole spacing (vertical or horizontal). Keypad reader housing latches onto mounting plate, secured with a screw. Mounts
on metal with minimal read range impact. An optional spacer can be used for surface mount installations.
Indoor/Outdoor Design
Rugged, weatherized polycarbonate enclosure designed to withstand harsh environments provides reliable performance and resistance to vandalism. Permanent magnet built into housing facilitates
tamper alarm when used with a magnetic reed switch.
Warranty
Warranted against defects in materials and workmanship for life. (See complete warranty policy for details.)
Base Part Numbers
RK40 Read Only Keypad: 6130
RWK400 Reader/Writer Keypad: 6131
Options
Color - Black, Gray
Key Management - Standard or High Security
Selectable Output Type (for MIFARE cards)
Termination - removable connector with miniature screw terminals or 18" (45.72 cm) wire pigtail.
Programmable LED/Beeper operation
Accessory - Security Tool; 04-0001-03
|
|
|
 |
|
 |
|
|
|
